top of page

Trenching Contractor or Electrician: Who Do You Actually Need?

Kris Goff
Sep 21
4 min read

Short answer: a trenching contractor digs the trench. A registered electrician installs, tests and certifies the cable. Those are two different trades and two different legal responsibilities. If you hire a digger crew for an electrical run, you still need an electrician at the end of it — and if you hire an electrician, somebody still has to dig. We do both with one crew, because we have a skilled digger operator on staff.

Why this trips people up

Search for trenching and you will find civil contractors — directional drilling, pipe laying, cable laying, fibre. Good operators, genuinely skilled at getting a conduit from A to B. What they generally cannot do is connect that cable to your switchboard, test it, and issue the certificate, because that is prescribed electrical work and it requires a registered electrical worker.

Search for an electrician and you will find someone who can do all of that, and who will then book a digger contractor for the trench — sometimes the very same civil firm — and pass the cost through with their margin on it.

What each party is actually responsible for

The trenching contractor

  • Getting the trench in at the right depth and route.

  • Working around services already in the ground.

  • Bedding, backfill and reinstatement of the ground.

  • Laying conduit or duct where that is the scope.

The registered electrician

  • Sizing the cable for the distance, not only the load — a long run needs a bigger cable than the current alone suggests.

  • Correct depth and mechanical protection for the cable type, under AS/NZS 3000.

  • Marker tape above the run so the next person with a digger finds out before the bucket does.

  • Terminations at both ends, protection at the board, and local isolation.

  • Testing, and the Certificate of Compliance. Mains-level work also gets a Record of Inspection.

That last line is the one that matters legally. Nobody but a registered electrical worker can sign it, and without it you have an uncertified installation in the ground.

How a trenched electrical run actually goes

  1. Scope and route. Where it starts, where it ends, what it crosses, what is already buried.

  2. Cable sizing. Distance and load together. This decides the trench width and the cost before anyone digs.

  3. Locate existing services. Before the bucket goes in, not after.

  4. Dig. Depth set by the cable type and by what crosses the run — deeper under a driveway or where stock and vehicles cross.

  5. Lay and bed. Cable or conduit in, bedded properly, marker tape over the top.

  6. Backfill and reinstate. Compacted, and the surface put back.

  7. Terminate, protect and test at both ends.

  8. Certify. Certificate of Compliance issued, and a Record of Inspection where the work requires one.

Steps 2, 7 and 8 are electrical work. Steps 4 to 6 are digging. Run them as two contracts and the join between them is where the arguments happen.

The practical case for one crew

  • One quote. No allowance for a trench somebody else prices later.

  • One party responsible. If the cable is wrong for the trench, or the trench is wrong for the cable, there is nobody to point at.

  • No scheduling gap. An open trench waiting on a second contractor is a hazard and a weather risk.

  • Spare conduit while the ground is open — a second duct for a future light, sensor or EV charger costs very little at the time and a great deal afterwards.

When a dedicated trenching contractor is the right call

Worth saying plainly. If the job is a long civil run, a major bore under a road, or a fibre or water main with no electrical component, a specialist civil contractor with the bigger gear is the better choice. We are electricians who dig our own runs — we are not a civil earthworks company, and we will say so.

And to be explicit about scope: we are not registered drainlayers. Wastewater and stormwater drainage is not work we take on.

Questions we get asked

Can a trenching contractor lay my power cable?

They can put it in the ground. They cannot connect it at the board, test it, or certify it. You will still need a registered electrician for that part.

Is it cheaper to hire the digger separately?

Occasionally, on a very large dig where specialist gear wins. On a typical supply run to a shed, pump or second dwelling it is usually not, once you count the coordination, the second mobilisation and the margin an electrician adds to a subcontracted trench.

How deep does an electrical cable have to be?

It depends on the cable type and what crosses the run — deeper under vehicle crossings and where mechanical protection is needed. AS/NZS 3000 sets it. That is exactly the sort of thing an electrician has to get right and a digger operator is not required to know.

Do you do the whole job in one visit?

Usually. Dig, lay, terminate and test in one mobilisation where the scope allows. More on the underground services page and in getting power to a shed or sleepout.

What does it cost?

Defined runs get a fixed price after a site visit. Distance, ground conditions and what the run crosses are the drivers. See what an electrician costs in the Waikato.

Get a trenched electrical run quoted

Tell us where it starts, where it ends and what it crosses. Call Kris on 021 466 666. We cover the Waikato and South Auckland from Waerenga — registered since 2013, EWRB E 243698.

Recent Posts

See All

Comments


Commenting on this post isn't available anymore. Contact the site owner for more info.
bottom of page