Where is Cosine based and what areas do you cover?

Cosine Electrical is based at Waerenga in the North Waikato, between Te Kauwhata and Morrinsville. We cover the wider Waikato and South Auckland — from Manukau down to Te Awamutu, east to Thames, west to Raglan. Drive times from Waerenga: Hamilton 30-40 minutes, Cambridge 40 minutes, Pukekohe 30 minutes, Manukau 45 minutes, Raglan 75 minutes, Thames 60 minutes.

What is the digger operator on the crew thing?

Most electricians sub-contract digging for underground work — second contractor, second quote, second site visit. Cosine has a skilled digger operator on the crew, so for underground jobs we trench our own runs. One quote, one team, one site visit. Note: Cosine is not a registered drainlayer. Wastewater and stormwater scope sits with a licensed drainlayer.

How quickly do you get back with a quote?

Within 24 hours of the site visit. Itemised, in writing, valid 30 days. For smaller jobs we can often give a rough indication over the phone if you text photos of the existing setup.

What does a switchboard upgrade cost?

A straight switchboard upgrade in an average three-bedroom Waikato house is typically $1,500-$2,500 plus GST for board and labour. Push-ups: old cable failing insulation tests, mains upgrade needed (lines company involvement), asbestos in the meter-box backing board common in 60s and 70s houses. Everything flagged in the written quote — no surprises on the invoice.

What does an EV charger install cost?

Standard install with the existing switchboard up to spec is $1,200-$1,800 plus GST plus the charger. Older home needing a board upgrade adds $1,500-$2,500. Long trenched runs to a detached garage on a lifestyle block typically $2,500-$4,500 all-in.

Do you do compliance testing for landlords?

Yes — landlord WOF-equivalent inspections, RCD function tests, written reports with photos and plain-English findings. Insurance-ready paperwork.

Do you work with builders on renovations?

Yes — preferred sparky for several builders across Hamilton, Cambridge and Pukekohe. We walk through with the homeowner and builder before quoting, mark up the plans, and work to the builder's schedule. We don't hold up the next trade.

Can you handle commercial maintenance for property managers?

Yes — scheduled maintenance contracts, emergency callouts, fault-finding, compliance reporting. One number, one paperwork system, no padded packages and no lock-ins.

Do you certify the work?

Always. Every new circuit and every board upgrade gets a Certificate of Compliance emailed through within a day of the job finishing. Required for insurance, future sale and any audit.

What if you cannot fix a fault in one visit?

Some faults like earth leakage on a circuit shared by multiple cables genuinely need a second visit. Day 1 we isolate the faulty section onto its own RCBO so the rest of the house keeps power. Day 2 we test and replace the bad section. We don't punch holes in walls to brute-force the search.

WiFi Heater Install in Thames — Redwood, Rinnai, Goldair and the Coastal-Heritage Mix

Kris Goff

Jun 18

1 min read

WiFi Heater Install in Thames — Redwood, Rinnai, Goldair and the Coastal-Heritage Mix

Call Kris on 021 466 666

Thames heater installs combine two distinct worlds — heritage gold-mining-era cottages in the central streets, and a long ribbon of coastal bach properties down the Te Puru and Tararu coast.

What a WiFi heater install actually involves

Plug-in — heater plugs into existing socket.
New socket + plug-in — surface mount or wall chase for the new socket.
Permanently wired — higher wattage, bathrooms, dedicated switching.

Permanent installs tested and certified.

What's specific to Thames WiFi heater installs

Heritage central Thames (Pollen Street, Mary Street) — heritage cottages with 1900s wiring under 60s-70s switchboards. Plug-in often the heritage-friendly default.
Coastal bach properties (Te Puru, Tararu, Thames-Tapu Coast Road) — intermittent use, salt corrosion, absentee owners. We do bach installs for Auckland/Hamilton owners regularly — quote off photos, schedule access.
Newer residential and Kauaeranga Valley homes — standard installs.
Scheduling matters for bach owners — WiFi scheduling saves real money when the bach is empty.
Heritage building considerations — surface-mount conduit, no aggressive cuts.

Brand options

Redwood WIFI V2, Rinnai, Goldair, Devola, Bromic.

What it costs

Plug-in install $150-$250. New socket + heater install $300-$550. Permanent wired install $400-$700, heritage homes $600-$900. Multi-heater (4-6 rooms) $1,200-$1,800. Bach absentee-owner install — no extra coordination cost. Switchboard upgrade adds $1,500-$2,500.

Call Kris on 021 466 666

For absentee bach owners: photos of the rooms and switchboard plus the heater models — we'll quote and arrange access.

WiFi Heater Install in Thames — Redwood, Rinnai, Goldair and the Coastal-Heritage Mix

WiFi Heater Install in Thames — Redwood, Rinnai, Goldair and the Coastal-Heritage Mix

What a WiFi heater install actually involves

What's specific to Thames WiFi heater installs

Brand options

What it costs

Call Kris on 021 466 666

Recent Posts

Comments