Where is Cosine based and what areas do you cover?

Cosine Electrical is based at Waerenga in the North Waikato, between Te Kauwhata and Morrinsville. We cover the wider Waikato and South Auckland — from Manukau down to Te Awamutu, east to Thames, west to Raglan. Drive times from Waerenga: Hamilton 30-40 minutes, Cambridge 40 minutes, Pukekohe 30 minutes, Manukau 45 minutes, Raglan 75 minutes, Thames 60 minutes.

What is the digger operator on the crew thing?

Most electricians sub-contract digging for underground work — second contractor, second quote, second site visit. Cosine has a skilled digger operator on the crew, so for underground jobs we trench our own runs. One quote, one team, one site visit. Note: Cosine is not a registered drainlayer. Wastewater and stormwater scope sits with a licensed drainlayer.

How quickly do you get back with a quote?

Within 24 hours of the site visit. Itemised, in writing, valid 30 days. For smaller jobs we can often give a rough indication over the phone if you text photos of the existing setup.

What does a switchboard upgrade cost?

A straight switchboard upgrade in an average three-bedroom Waikato house is typically $1,500-$2,500 plus GST for board and labour. Push-ups: old cable failing insulation tests, mains upgrade needed (lines company involvement), asbestos in the meter-box backing board common in 60s and 70s houses. Everything flagged in the written quote — no surprises on the invoice.

What does an EV charger install cost?

Standard install with the existing switchboard up to spec is $1,200-$1,800 plus GST plus the charger. Older home needing a board upgrade adds $1,500-$2,500. Long trenched runs to a detached garage on a lifestyle block typically $2,500-$4,500 all-in.

Do you do compliance testing for landlords?

Yes — landlord WOF-equivalent inspections, RCD function tests, written reports with photos and plain-English findings. Insurance-ready paperwork.

Do you work with builders on renovations?

Yes — preferred sparky for several builders across Hamilton, Cambridge and Pukekohe. We walk through with the homeowner and builder before quoting, mark up the plans, and work to the builder's schedule. We don't hold up the next trade.

Can you handle commercial maintenance for property managers?

Yes — scheduled maintenance contracts, emergency callouts, fault-finding, compliance reporting. One number, one paperwork system, no padded packages and no lock-ins.

Do you certify the work?

Always. Every new circuit and every board upgrade gets a Certificate of Compliance emailed through within a day of the job finishing. Required for insurance, future sale and any audit.

What if you cannot fix a fault in one visit?

Some faults like earth leakage on a circuit shared by multiple cables genuinely need a second visit. Day 1 we isolate the faulty section onto its own RCBO so the rest of the house keeps power. Day 2 we test and replace the bad section. We don't punch holes in walls to brute-force the search.

WiFi Heater Install in Hamilton — Redwood, Rinnai, Goldair and How to Do It Right

Kris Goff

Jun 18

1 min read

WiFi Heater Install in Hamilton — Redwood, Rinnai, Goldair and How to Do It Right

Call Kris on 021 466 666

Hamilton's winter heating mix has shifted hard in the last few years. Heat pumps as the primary, WiFi panel heaters in the bedrooms, study and any zones the heat pump doesn't reach well.

What a WiFi heater install actually involves

Plug-in (under 2kW) — straightforward if the existing socket is in the right place.
New socket + plug-in — for when the existing socket is in the wrong spot.
Permanently wired — required for higher-wattage units, bathrooms, dedicated switching.

Certificate of Compliance issued for permanent installs.

What's specific to Hamilton WiFi heater installs

Newer subdivision homes (Rototuna, Flagstaff, Peacockes, Amberfield) — modern switchboards, often heat pump as primary with WiFi panel heaters for bedrooms.
Older inner Hamilton (Glenview, Hillcrest, Forest Lake, Maeroa, Claudelands, Frankton) — original boards from 60s-70s may need an RCBO add or board lift before new permanent circuits.
CBD townhouses and unit blocks — body corp considerations.
Lifestyle blocks at Tamahere, Newstead, Matangi — multi-heater jobs are common.
Rental properties — landlords sometimes want plug-in heaters rather than permanent wiring.

Brand options

Redwood WIFI V2, Rinnai, Goldair, Devola, Bromic (outdoor).

What it costs

Plug-in install $150-$250. New socket $300-$500. Permanent wired $400-$700. Multi-heater (4-6 rooms, one visit) $1,200-$1,800. Switchboard upgrade adds $1,500-$2,500.

Call Kris on 021 466 666

Send photos of where each heater needs to go, plus the heater wattage.

WiFi Heater Install in Hamilton — Redwood, Rinnai, Goldair and How to Do It Right

WiFi Heater Install in Hamilton — Redwood, Rinnai, Goldair and How to Do It Right

What a WiFi heater install actually involves

What's specific to Hamilton WiFi heater installs

Brand options

What it costs

Call Kris on 021 466 666

Recent Posts

Comments